Open dishwasher with murky standing water on the tub floor around a filter clogged with food scraps

Dishwasher Not Draining: Causes and Safe Fixes

Open empty dishwasher beside white kitchen cabinets, with the lower rack and cutlery basket pulled out.
An open, empty dishwasher in a modern kitchen, with the lower rack pulled forward. Photo: Castorly Stock / Pexels

Quick answer

When a dishwasher leaves standing water in the tub after a cycle, the cause is usually in the drain path. Official support pages from KitchenAid, Whirlpool, Samsung, GE Appliances, and Bosch point to a clogged filter, debris in the sump (the well under the filter), a kinked or clogged drain hose, a clogged air gap, a garbage disposal that is clogged or still has its knockout plug in place, or a jammed drain pump. A small amount of water in the filter area can be normal. Start with the filter and the hose. If those checks do not restore draining, the drain pump may need attention.

Quick diagnosis table

Symptom Possible cause First check
A little water in the filter area Often normal on many models Confirm the water level first
Standing water slightly above the filter Partial restriction in the drain path Clean the filter and the sump
Water near the door after a cycle Severe blockage or the pump is not running Check the hose, air gap, and pump area
Will not drain after a new disposal or dishwasher Knockout plug still in place Check that the knockout plug was removed
The kitchen sink itself will not drain Problem is the home’s plumbing Run water in the connected sink
Still will not drain after every check Possible drain pump failure Get a professional diagnosis

Safety first

  • Disconnect power before you reach into the dishwasher. Unplug it or switch off its circuit breaker. KitchenAid says not to rely on the control panel alone.
  • Wear protective gloves. Sharp debris, including broken glass, can collect in the filter and pump area.
  • Never put your hands into a garbage disposal to check it. GE Appliances warns that a serious injury could occur.
  • Do not use chemical drain cleaners or bleach in the dishwasher. KitchenAid, Whirlpool, GE Appliances, and Bosch warn that these products can damage seals and other parts. Clear blockages by hand.
  • Keep towels and a bucket nearby for standing water and hose checks.

Read our full Safety Disclaimer before you start. Stop and call a technician if you smell burning, see damaged wiring, or the breaker trips.

Soapy standing water covering the bottom of a dishwasher tub around the lower spray arm and filter.
Standing soapy water in the bottom of an open dishwasher, around the lower spray arm and filter. Photo: Edward Nelson / Wikimedia Commons, Public Domain

How to confirm it is a drain problem

A little water in the filter area is not always a fault. GE Appliances says that on models without an Ultra Fine filter, 1 to 2 cups of clean water covering the bottom of the tub can be normal. On models with an Ultra Fine filter, water in the sump is normal, but it should not cover the bottom of the tub. Whirlpool says a small amount of standing water in the filter area, about halfway up, is normal and is replaced at the start of the next cycle.

When the level is higher, KitchenAid notes that water slightly above the filter often means a partial restriction, water near the door suggests a severe blockage or a pump that is not running, and a steady hum or grinding can mean a jammed impeller or hard debris such as glass. Bosch uses E24 and E25 for drain problems. Samsung lists 5C, 5E, OC, and OE as drain or overflow errors. Before you order any part, write down your full model number. See How to Find Your Model Number.

Open dishwasher with murky standing water on the tub floor around a filter clogged with food scraps
Standing water over a clogged filter is the most visible sign of a drain problem. Illustration only.
Video: Dishwasher Not Draining — Dishwasher Troubleshooting (RepairClinic.com).
Under-sink plumbing with a garbage disposal, white drain pipes, and a black dishwasher drain hose.
A garbage disposal under a kitchen sink, with the dishwasher drain hose connected to it. Photo: Tony Webster / Wikimedia Commons, CC BY 2.0

Safe checks to fix a dishwasher that is not draining

  1. Turn off and disconnect power. If you will disconnect the drain hose, KitchenAid also recommends shutting off the water supply valve. Bail standing water into a bucket.
  2. Clean the filter and the sump. Remove the filter as your manual describes and rinse it under running water with a soft brush. Do not use anything abrasive. Take debris out of the sump and reinstall the filter so it locks. Samsung notes that missing or incorrectly inserted filter parts can themselves cause drain problems.
  3. Check the drain hose for kinks and pinches. The hose should not be kinked, crushed, or pinched behind the dishwasher or under the sink. Samsung says a common issue right after installation is the dishwasher sitting on its own hose. If the hose is damaged, stop and get help rather than forcing it.
  4. Confirm a high loop or a clear air gap. Samsung, KitchenAid, Whirlpool, and GE Appliances say the hose should either rise in a high loop under the counter or connect through an air gap, depending on local codes and your installation instructions. Without one of these, wastewater can flow back into the dishwasher. Do not guess at a height.
  5. Check the garbage disposal and the knockout plug. If the dishwasher drains into a disposal, GE Appliances recommends running the disposal before a cycle. After a new disposal or dishwasher is installed, the knockout plug (Samsung calls it the disposal cap) may still be in the disposal’s dishwasher inlet and can block draining completely. KitchenAid’s check: with power off, disconnect the hose over a bucket and insert a pencil into the inlet. The plug is recessed and not visible from the side. If the pencil can go in about 3 inches, the plug has been removed.
  6. Clean the air gap, if you have one. An air gap is the small cylinder on the sink or countertop. GE Appliances and Whirlpool say to remove the cap and clean out debris. If water spills from the air gap into the sink during a drain, KitchenAid says the blockage is downstream.
  7. See whether the sink itself drains. Samsung’s test is to run water in the connected sink for about 30 seconds. If the sink does not drain, the problem is the home’s plumbing, and a plumber is the right call.
  8. Check the drain pump only if your manual shows how. On many Bosch dishwashers, the pump cover is under the filter; you can clear debris and confirm the impeller turns freely. See our Bosch E25 guide for those steps. Do not take the pump or electrical parts apart unless your manual describes it. Then restore power and run a short rinse cycle to test.
Video: How to Install a Dishwasher Drain Hose (Whirlpool Service).

Still not draining?

Some dishwashers have a check valve, also called an anti-backflow valve, in the drain path. GE Appliances says its dishwashers have a built-in anti-backflow wash/drain diverter valve in the pump housing. It opens the drain port when the dishwasher pumps out and helps keep soiled water from flowing back into the tub. GE still requires a high drain loop as described in the model’s installation instructions. Manufacturer “not draining” guides do not list this valve as a first home check. If the steps above are clear and the dishwasher still will not drain, a technician can inspect the pump and valve. Do not order a check valve until the exact part for your model has been identified.

If the drain path is clear, the drain pump may be jammed or failed. KitchenAid, Whirlpool, and GE Appliances recommend service when cleaning and hose checks do not fix it. Less common causes include a timer, a drain solenoid on some older designs, or a control board. Over-sudsing can also interfere with draining; GE says the wrong detergent, or too much of it, can cause this. Use automatic dishwasher detergent only. Do not test electrical parts yourself. Stop if you notice a leak, a burning smell, or a breaker that trips.

Need a pro? If any step feels unsafe or the problem keeps coming back, see when to call an appliance technician and how to prepare for the visit.

Likely replacement part: drain pump

When the drain path is clear and the dishwasher still will not empty, the part to suspect next is the drain pump. The correct pump depends on your brand and exact model number. Bosch owners should match the pump using the part information in our E25 and E24 guides.

Find the right part by your model number: check the Whirlpool drain pump on AppliancePartsPros and confirm it fits your exact model before you order. Not sure where the model number is? See How to Find Your Model Number.

Example: genuine Whirlpool drain pump, part number WPW10348269, was listed at $62.61 on AppliancePartsPros.com when we checked on November 21, 2026. AppliancePartsPros lists this pump for Whirlpool, KitchenAid, Maytag, and other Whirlpool-family brands, but only if it matches your model. Prices change; the retailer’s page shows the current price and whether it fits.

Replacing a drain pump means disconnecting the dishwasher from power and water and working underneath or inside the unit. If you have not done this kind of repair before, consider having a technician install it.

Related guides

FAQ

Is some water in the bottom of the dishwasher normal?

Yes, a small amount can be. GE Appliances and Whirlpool both describe a little clean water in the filter or sump area as normal on many models. Water that covers the tub floor on a model that should only have water in the sump, or water that reaches the door, is worth checking.

What is a garbage disposal knockout plug?

It is a plug in the disposal’s dishwasher inlet that must be removed when the dishwasher is connected to the disposal. If it is left in, the dishwasher cannot drain. KitchenAid, Whirlpool, GE Appliances, Samsung, and Bosch all list a leftover plug as a possible cause after a new install.

Do I need an air gap or a high loop?

You need one or the other, and sometimes both, depending on local plumbing codes and your model’s installation instructions. An air gap sits on the sink or countertop. A high loop is the drain hose routed up under the counter before it connects to the drain.

Can I pour drain cleaner into the dishwasher?

No. KitchenAid, Whirlpool, GE Appliances, and Bosch advise against chemical drain cleaners in the dishwasher because they can damage components. Clear the blockage by hand.

When should I call a technician, and when a plumber?

If the kitchen sink itself will not drain, Samsung says the problem is the home’s plumbing and a plumber is the right call. If the sink drains but the dishwasher does not after the checks above, an appliance technician can test the pump and related parts.

Need a hand?

If the safe checks did not fix it, a professional can diagnose the pump and replace the right part for your model.

Need a pro? If any step feels unsafe or the problem keeps coming back, see when to call an appliance technician and how to prepare for the visit.

Disclosure: some links in this article are affiliate links. If you buy a part or book a service through them, we may earn a commission at no extra cost to you. Learn more.

Sources

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *